IEC 61851-22:2001 pdf download.Electric vehicle conductive charging system
I Scope
This part of IEC 61851, together with part 1, gives the requirements for a.c. electric vehicle charging stations for conductive connection to an electric vehicle, with ac. supply voltages according to IEC 60038 up to 690 V.
This standard does not cover all safety aspects related to maintenance.
The scope of this part of IEC 61851 does not cover box type assemblies with socket-outlets, installed for the purpose of delivering energy to the vehicle, which have no charging control functions.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of IEC 61851. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of IEC 61851 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards.
IEC 60038:1983, IEC standard voltages
IEC 60068-2-1:1990, Environmental testing — Part 2: Tests — Tests A: Cold
IEC 60068-2-2:1974, Environmental testing — Part 2: Tests — Tests B: Dry heat
IEC 60068-2-3:1969. Environmental testing — Part 2: Tests — Test Ca: Damp heat, steady state
IEC 60068-2-5:1975, Environmental testing — Part 2: Tests — Test Sa: Simulated solar radiation at ground level
IEC 60068-2-14:1 984, Environmental testing — Part 2: Tests — Test N: Change of temperature
IEC 60068-2-30:1980, Environmental testing — Part 2: Tests — Test Db and guidance: Damp heat, cyclic (12 + 12-hour cycle)
IEC 60068-2-52:1996, Environmental testing — Part 2: Tests — Test Kb: Salt mist, cyclic (sodium chloride solution)
IEC 60068-2-75:1 997, Environmental testing — Part 2: Tests — Test Eh: Hammer tests
IEC 60364-4-43:1977, Electrical installations of buildings — Part 4: Protection for safety — Chapter 43: Protection against overcurrent
IEC 60364-4-443:1995, Electrical installations of buildings — Part 4: Protection for safety — Chapter 44: Protection against overvoltages — Section 443: Protection against overvoltages of atmospheric origin or due to switching Amendment 1 (1998) 1)
IEC 60439-1 :1999 Low-voltage switchgear and controlgear assemblies — Part 1: Type-tested and partially type-tested assemblies
IEC 60529:1989, Degrees of protection provided by enclosures (IP Code)
IEC 60664-1 :1992, Insulation coordination for equipment within low-voltage systems — Part 1:Principles, requirements and tests
IEC 60950:1999, Safety of information technology equipment
IEC 61000-2-2:1990, Electromagnetic compatibility (EMC) — Part 2: Environment — Compatibility levels for low-frequency conducted disturbances and signalling in public low- voltage power supply systems
IEC 61000-3-2:2000, Electromagnetic compatibility (EMC) — Part 3-2: Limits — Limits for harmonic current emissions
IEC 61000-4-1:2000, Electromagnetic compatibility (EMC) — Part 4-1: Testing and measurement techniques — Overview of IEC 61000-4 series
IEC 61000-4-2:1995, Electromagnetic compatibility (EMC) — Part 4-2: Testing and measurement techniques — Section 2: Electrostatic discharge immunity test — Basic EMC publication 2) Amendment 1 (1998) Amendment 2 (2000)
IEC 61000-4-3:1995, Electromagnetic compatibility (EMC) — Part 4: Testing and measurement techniques — Section 3: Radiated, radio-frequency, electromagnetic field immunity test 3) Amendment 1 (1998) Amendment 2 (2000)
IEC 61000-4-4:1995, Electromagnetic compatibility (EMC) — Part 4: Testing and measurement techniques — Section 4: Electrical fast transient/burst immunity test — Basic EMC publication Amendment 1 (2000)
IEC 61000-4-5:1995, Electromagnetic compatibility (EMC) — Part 4: Testing and measurement techniques — Section 5: Surge immunity test.IEC 61851-22 pdf download.